DIGITAL SURFACE PROFILE GAUGE (TQC, NETH.)

Digital Surface Profile acc. 0.002mm Range : 0-1000 microns 
Acc. ±1 microns for checking sand blasting, shot blasting &grit blasting surface

.

DIAL SURFACE PROFILE GAUGE

Surface Profile Gauge Indian Make

Dial type Gauge with accuracy of .002 mm for checking height of peak & depths of valley & measuring the surface finish in micron directly. Range 0-1000 Microns. It is a dial gauge mounted on large base foot in the centre of which is a precision-ground tungsten carbide tip. Accry 2 Microns.  

.

PIN HOLE DETECTORS

Indian made pinhole detector for checking any pinhole or defects on paint coated surface. with Sponge Prob
Range : 0-300 microns & 9 Volts
Pinhole Detector Heavy Duty 0-500 microns and Digital Range : 9,6.7 & 90 Volts. Combine

.

HOLIDAY DETECTOR U.K./ U.S.A.

Battery operated with voltage output of 0-15 KV & 0-30 KV. checks Bitumen or Epoxy on concrete eg. Storage tanks, water and sewage treatment facilities. Testing insulating coating on oil, gas & water pipelines. Provided rechargeable battery earth lead, high voltage probe, handle & lead band brush probe.

.

TESTEX TAPES USA

Elcometer U.K. 122 Testex Tapes provides a quick, easy to use low cost method of measuring rough surface profiles after shot or grit blasting. Used in conjuction with the tape gives peak to valley height. This method enables a replica of the anchor pattern profile to be produced, which can then be attached to a report, to provide a permanent record for future reference. Set of 50 replicas per roll.
Ranges Coarse E122...B Coarse 50 Microns, and X Coarse 37-100 microns Model E-122. Foil Thickness Gauge 1 micron Accuracy . For checking thickness of impressions for above.

.

TESTEX GAUGE FOR PRESS-O-FILM

Acc. of 0.01mm , Range 0 to 10mm, Acc. 0.01mm for checking diameter thickness of small components and checking the thickness of sheets, papers, cardboards on any type of flat sheets.

.

DIGITAL THERMOMETER

For checking temperature 0-1000º C with standard Probe.
for checking surface temperature. Also available thermemeter from -60 to 1200ºC The Digital Thermometer are Available long needle probes for checking Temperature liquids or Air

.

SWEDISH STANDARD BOOK (SWEDEN)

With various chart, colored actual photos & plates of rust checking & surface finish of Shot Blasting Sweden as per DIN Standard, ASTMBS Standard, ISO 8501-1-1988 & SS 055900. Finishes of surfaces checking SA2,2.5 & 3. SSPC - VIS - 1 Visual standards for Abrasive blast cleaning surfaces USA SSPC - VIS - 3 Visual standards for powder & Hand Tool cleaning steel. USA

.

WET FILM THICKNESS COMB USA MAKE

Range : 25 to 2032 Microns Scale on all 4sides of gauge of Aluminum. Wet film comb USA Stainless Steel Range 25 to 3000 Microns

.

BRESLE - KIT CHLORIDE TEST KIT (USA / TQC, NETH.)

The Bresle KIT - Chloride Test Kit includes all the necessary equipment for assessing the level of soluble salts on blast-cleaned surfaces prior to coating. Inside the Bresle KIT - Chloride Test Kit is a conductivity gauge used for the assessment of soluble salt ions as chlorides, sulphates and nitrates. The Bresle Method described in the ISO 8502-6 and ISO 8502-9 standard, states that the conductivity is mainly directly proportional to the concentration of dissolved chloride ions in the solution.

.

HYPERDEMIC NEEDLE PRESSURE

Hyperdemic Needle Pressure Gauge USA make pocket size to 
determine blast cleaning air pressure at the nozzle. Instant 
reading from 0-160 Psig. 
Accuracy + 5%.

.

CLEMXEX PRESSURE BLAST ANALYER

USA make portable hand held for measuring the orifice in inches & air consumption 
( CFM @ 100 PSI) of an abrasive blasting nozzle.

.

CROSS CUT ADHESION TEST KIT

.

FLASH MAGNIFIER

.

SURFACE COMPARATOR

.

SURFACE ROUGHNESS COMPARATOR

Surface Comparator – USA Make  

allows the estimation of the surface roughness by both touch & sight in accordance 

with ASTM D2217N method A and ISO8503 

for Grit Blasting / Shot Blasting.

.

DUST TEST KIT TQC NETHERLAND

.

MAGNETIC THERMOMETER

.