Gala Screened Separable Connectors are designed to connect single and three core polymeric cables to medium voltage switchgear and other equipment using bushings type "C" specified for 630A upto 24kV. Made of a highly modified EPDM rubber and protected by a touch proof outer conductive screen connected to earth

Supporting a wide application range, the design incorporates one body and stress cone adapters to cover all cross section from 25 to 300 sq. mm. All kits include high-performance multi range compression lugs matching the design of the design of the connector.

Bus Tube is heat shrinkable tube designed to insulate busbar systems up to 66KV & to protect against accidental flash-over. The tubes are manufactured from high quality non tracking cross-linked polyolefin material. Meets ANSI C37.20.2 standards for switchgear application up to 66 KV.

• Long Life
• Suitable for polluted environments, salty atmospheres etc.
• Unique self cleaning property
• Resistance to breakage and vandalism, practically unbreakable
• Superior anti-tracking properties
• High mechanical strength
• Light weight
• Ease of installation
• Choice of end fittings
• Long term surface hydrophobicity
• Compliance with IEC 61109, CEA LWIWG-01(91), ANSI C29.11-1989

Tamper Proof End Seal is Heat Shrink End Cap, used to seal the ends of all types of Cables & to protect it from ingress of water/moisture. The caps are manufactured from high quality cross linked polyolefin material.

Tamper Proof Features / Benefits :

• Permanent Foolproof Seal to the Cable end.
• Can not be tampered, removed or re-used.
• Can be considered as Factory fitted Cable end seal.
• Customised Logo Printing with Special High Performance Non Removable Ink.
• Warranty of Cable length can be considered as void in case Cable is found without Tamper Proof end seal.
• Avoids unwanted customer claims for Shortage/Pilferage of Cable length.

These Heat Shrink End Caps with Cable Pulling Eye for Telephone and Power cable are the ultimate solution in cable pulling eyes. These caps with pulling eye form a connection as strong as the cable itself. The entire cable, jacket and conductor, is used which reduces the risk of cable deformation during pulling. When properly installed, Heat Shrink End Caps with Cable Pulling Eye are virtually impossible to pull off and also seal the cable against both water and moisture intrusion. Typically factory installed, the pulling eyes can also be field installed with a propane (preferred) or butane gas torch.

Insulshroud is flexible electrical insulating boot / shroud, made from specially formulated Polyvinyl chloride (PVC) material to provide excellent electrical insulation and to with stand higher operating temperature continuously.

This is designed to prevent electrocution of bird and animal wildlife and the resulting incidence of power outages. The ability to mould to any size of shape in any quantity with low tooling cost and quick delivery gives an enormous range of applications in the electrical industries.

Insulcover is a Medium Voltage Wrap Around Overhead Line Cover that provides retrofit insulation for overhead conductors to help prevent electrical outages caused by trees or wildlife coming into the contact with distribution lines.

It is manufactured from high quality Non Tracking Crosslinked Polyolefin material.

IInsulcover is designed to insulate existing bare lines without costly conductor replacement expenditure or additional line hardware. Insulcover may be applied selectively on problem spans when temperatures are above 0oC.

Installation is possible on energized lines utilizing the Split Insulation Tool which attaches directly to the overhead conductor and remains stationary ina single location.

Hot melt adhesive lining provides 100% environmental sealing against weathering, moisture, contamination and adverse environmental conditions according to IP 68.
Resistance to UV rays & Ozone.
Versatile and cost effective, as 5 sizes of Pole Cap covers Pole dia. from 140 mm to 460 mm.
Service life of Pole Cap is more than 30 years.
Easy installation on concrete, wood, steel or composite poles in minutes.

Polecap / Dock Pile Cap is used to cover the top of the Power Pole & Dock Pile. It prevents birds from perching on top of the pole while protecting the top of the pole from rain and decay, thereby increasing Pole life. The caps are manufactured from Specially formulated Polyvinyl Chloride (PVC) material to provide excellent mechanical and electrical insulation.

As the major producer of PVC caps in the world, Galathermo has the widest line of caps, plugs, flange covers, and products available. Of course, this broad line of products evolved due to the individual compensation that plugs have over nearly all hard plastic closures.

• Vin cap is made from specially formulated Poly Vinyl Chloride material.
• Push-on type application.
• Ensures perfect protection to cable ends from weathering, moisture and contamination.
• Quick and easy installation without any tools. No skill is required.
• Extremely economical and cost effective compared to Heat Shrink End Caps.
• Caps of varying lengths & thickness can be made with no tooling charge.
• Will not Crack or Split like Low Density Polyethylene.

Constant Force Spring are made from Stainless steel material & it is no current carrying parts.

It is used for solder free electric connection between metal cable elements & earthing device.

Also used for cast-resin,heat shrink and medium voltage joints.

Easily applied onto the sheath connection.

Corrosion free & mechanical stable.

Continues to exert constant pressure.

Mastic Tape is use for insulation in cable jointing kits to prevent it from corrosion to metal materials.It is excellent thermal insulation property & resistance to water,moisture climate & temperature.

The cut pieces are supplied sand withed in silicone coated paper,whereas for continuous rolls,it is spooled and interleaved with release paper/polyethylene & packed in a poly bag.

APPLICATION

• These controlled soldering devices are designed for termination of a bare or tin-plated copper shield on cable having an insulation rated for at least +85oC,meeting the dimensional criteria listed in the table above.
• Temperature range : -55o C to +125o C
• When installed properly ,it will meet the requirments for best results ,prepare the cable as shown: