Orifice Plates Water Flow Meter is an ace product from our side. These products from our side are most commonly used as primary element for flow measurement in pipelines based upon the principle of measurement of differential pressure created when an obstruction is placed in the fluid flow, due to increase in fluid velocity. This one is efficient enough to provide an acceptable level of uncertainties at superior performance and low maintenance without regular follow-ups.

Features:

Correct flow measurement
Accurate results
Easy to maintain

Applications:

Scientific laboratory
Research centres
Chemical industries

Specifications:

Available in SS-316/P.P. Material
1 ½” to 24” line sizes
DESIGN - Confirming to ISA RP 3.2, DN 1952, BS 1042, ISO-5167
ORIFICE BORE - Confirming to ISO 5167 / BS 1042 / RW Miller / L. K. SPINK / AGE – 3
ACCURACY - Within /- 1 %
VENT / DRAIN - Vent OR Drain holes are provided as per customer’s requirement. Not drilled for Orifice Bore smaller than 25.4 mm

.

Product Details:

Minimum Order Quantity 1 Piece
Brand Flowtech
Display Digital

Orifice Plate Meter gives an acceptable level of uncertainties at lowest cost and long life without regular maintenance. These products from our side are most commonly used as primary element for flow measurement in pipelines based upon the principle of measurement of differential pressure created when an obstruction is placed in the fluid flow, due to increase in fluid velocity.

Features:

Flow measurement
Perfect results
Simple to maintain

Applications:

Scientific laboratory
Research centres
Chemical industries

Specifications:

Available in SS-316/P.P. Material
1 ½” to 24” line sizes
Design - confirming to isa rp 3. 2, dn 1952, bs 1042, iso-5167
Orifice bore - confirming to iso 5167 / bs 1042 / rw miller / l. K. Spink / age – 3
Accuracy - within /- 1 %
Vent / drain - vent or drain holes are provided as per customer’s requirement. Not drilled for orifice bore smaller than 25. 4 mm

.

Product Details:

Size 2 inch, 3 inch, 2 TO 30 inch
Brand FLOWTECH

Applications:

Scientific laboratory
Research centres
Chemical industries

Specifications:

Available in SS-316/P.P. Material
1 ½” to 24” line sizes
Design - confirming to isa rp 3. 2, dn 1952, bs 1042, iso-5167
Orifice bore - confirming to iso 5167 / bs 1042 / rw miller / l. K. Spink / age – 3
Accuracy - within /- 1 %
Vent / drain - vent or drain holes are provided as per customer’s requirement. Not drilled for orifice bore smaller than 25. 4 mm

.

Applications:

Scientific laboratory
Research centres
Chemical industries

Specifications:

Available in SS-316/P.P. Material
1 ½” to 24” line sizes
Design - confirming to isa rp 3. 2, dn 1952, bs 1042, iso-5167
Orifice bore - confirming to iso 5167 / bs 1042 / rw miller / l. K. Spink / age – 3
Accuracy - within /- 1 %
Vent / drain - vent or drain holes are provided as per customer’s requirement. Not drilled for orifice bore smaller than 25. 4 mm

.

Applications:

Scientific laboratory
Research centres
Chemical industries

Specifications:

Available in SS-316/P.P. Material
1 ½” to 24” line sizes
Design - confirming to isa rp 3. 2, dn 1952, bs 1042, iso-5167
Orifice bore - confirming to iso 5167 / bs 1042 / rw miller / l. K. Spink / age – 3
Accuracy - within /- 1 %
Vent / drain - vent or drain holes are provided as per customer’s requirement. Not drilled for orifice bore smaller than 25. 4 mm

.

Product Details:

Minimum Order Quantity 1 Piece
Brand FLOWTECH
Size 5-10 inch, 10-20 inch, 20-30 inch
Material Standard ASTM A105, ANSI B16.5

DESCRIPTION :

Flowtech Make Orifice Plates & Flange Assemblies.
Suitable for creating differential pressure in a pipe line for flow transmitter etc.

Orifice flange assemblies’ consist of weld neck type flanges with studs, nuts, and gaskets.

Available in SS-316/P.P.Material.
Design standard confirm to BS 1042

FOWTECHmake ORIFICE FLANGE ASSEMBLIES are used for measuring flow of various Liquids, Gases & Steam from

1 ½”to 24” line sizes. It gives an acceptable level of uncertainties at lowest cost and long life without regular maintenances. Orifice Plates are most commonly used as primary element for flow measurement in pipelines based upon the principle of measurement of ‘Differential Pressure’ created when an obstruction is placed in the fluid flow, due to increase in fluid velocity.

Design Standards

DESIGN - Confirming to ISA RP 3.2, DN 1952, BS 1042, ISO-5167
ORIFICE BORE - Confirming to ISO 5167 / BS 1042 / RW Miller / L. K. SPINK / AGE – 3
ACCURACY - Within /- 1 %
VENT / DRAIN - Vent OR Drain holes are provided as per customer’s requirement. Not drilled for Orifice Bore smaller than 25.4 mm.

.

Applications:

Scientific laboratory
Research centers
Chemical industries

Specifications:

Available in SS-316/P.P. Material
1 ½” to 24” line sizes
Design - confirming to isa rp 3. 2, dn 1952, bs 1042, iso-5167
Orifice bore - confirming to iso 5167 / bs 1042 / rw miller / l. K. Spink / age – 3
Accuracy - within /- 1 %
Vent / drain - vent or drain holes are provided as per customer’s requirement. Not drilled for orifice bore smaller than 25. 4 mm

.

Product Details:

Minimum Order Quantity 1 Piece
Brand FLOWTECH
Size 1-5 inch, 5-10 inch, 10-20 inch, 20-30 inch
Material Standard ASTM A105, ANSI B16.5

Description:

Flowtech Make Orifice Plates & Flange Assemblies.

Suitable for creating differential pressure in a pipe line for flow transmitter etc.

'Orifice flange assemblies’ consist of weld neck type flanges with studs, nuts, and gaskets.

Available in SS-316/P.P.Material.
Design standard confirm to BS 1042

FOWTECHmake Orifice Flange Assemblies are used for measuring flow of various Liquids, Gases & Steam from

1 ½”to 24” line sizes. It gives an acceptable level of uncertainties at lowest cost and long life without regular maintenance. Orifice Plates are most commonly used as primary element for flow measurement in pipelines based upon the principle of measurement of ‘Differential Pressure’ created when an obstruction is placed in the fluid flow, due to increase in fluid velocity.

Design Standards

Design - Confirming to ISA RP 3.2, DN 1952, BS 1042, ISO-5167
Orifice Bore- Confirming to ISO 5167 / BS 1042 / RW Miller / L. K. SPINK / AGE – 3
Accuracy- Within /- 1 %
VENT / DRAIN - Vent OR Drain holes are provided as per customer’s requirement. Not drilled for Orifice Bore smaller than 25.4 mm.

.

Applications:

Scientific laboratory
Research centres
Chemical industries

Specifications:

Available in SS-316/P.P. Material
1 ½” to 24” line sizes
Design - confirming to isa rp 3. 2, dn 1952, bs 1042, iso-5167
Orifice bore - confirming to iso 5167 / bs 1042 / rw miller / l. K. Spink / age – 3
Accuracy - within /- 1 %
Vent / drain - vent or drain holes are provided as per customer’s requirement. Not drilled for orifice bore smaller than 25. 4 mm

.

Product Details:

Minimum Order Quantity 1 Piece
Brand FLOWTECH
Size 1-5 inch, 5-10 inch, 10-20 inch, 20-30 inch
Material Standard ASTM A105, ANSI B16.5

.

Product Details:

Minimum Order Quantity 1 Piece
Size 2 inch, 3 inch
Brand FLOWTECH

Applications:

Scientific laboratory
Research centres
Chemical industries

Specifications:

Available in SS-316/P.P. Material
1 ½” to 24” line sizes
Design - confirming to isa rp 3. 2, dn 1952, bs 1042, iso-5167
Orifice bore - confirming to iso 5167 / bs 1042 / rw miller / l. K. Spink / age – 3
Accuracy - within /- 1 %
Vent / drain - vent or drain holes are provided as per customer’s requirement. Not drilled for orifice bore smaller than 25. 4 mm

.

DESCRIPTION :

Flowtech Make Orifice Plates & Flange Assemblies.

Suitable for creating differential pressure in a pipe line for flow transmitter etc.

Orifice flange assemblies’ consist of weld neck type flanges with studs, nuts, and gaskets.

Available in SS-316/P.P.Material.
Design standard confirm to BS 1042

FOWTECHmake ORIFICE FLANGE ASSEMBLIES are used for measuring flow of various Liquids, Gases & Steam from

1 ½”to 24” line sizes. It gives an acceptable level of uncertainties at lowest cost and long life without regular maintenances. Orifice Plates are most commonly used as primary element for flow measurement in pipelines based upon the principle of measurement of ‘Differential Pressure’ created when an obstruction is placed in the fluid flow, due to increase in fluid velocity.

Design Standards

DESIGN - Confirming to ISA RP 3.2, DN 1952, BS 1042, ISO-5167
ORIFICE BORE - Confirming to ISO 5167 / BS 1042 / RW Miller / L. K. SPINK / AGE – 3
ACCURACY - Within /- 1 %
VENT / DRAIN - Vent OR Drain holes are provided as per customer’s requirement. Not drilled for Orifice Bore smaller than 25.4 mm.

.

Product Details:

Minimum Order Quantity 1 Piece
Brand FLOWTECH
Size 1-5 inch, 5-10 inch, 10-20 inch, 20-30 inch
Material Standard ASTM A105, ANSI B16.5

DESCRIPTION :

Flowtech Make Orifice Plates & Flange Assemblies.

Suitable for creating differential pressure in a pipe line for flow transmitter etc.

Orifice flange assemblies’ consist of weld neck type flanges with studs, nuts, and gaskets.

Available in SS-316/P.P.Material.
Design standard confirm to BS 1042 

   FOWTECH make ORIFICE FLANGE ASSEMBLIES are used for measuring flow of various Liquids, Gases & Steam from

1 ½” to 24” line sizes. It gives an acceptable level of uncertainties at lowest cost and long life without regular maintenances. Orifice Plates are most commonly used as primary element for flow measurement in pipelines based upon the principle of measurement of ‘Differential Pressure’ created when an obstruction is placed in the fluid flow, due to increase in fluid velocity.

Design Standards

DESIGN - Confirming to ISA RP 3.2, DN 1952, BS 1042, ISO-5167
ORIFICE BORE - Confirming to ISO 5167 / BS 1042 / RW Miller / L. K. SPINK / AGE – 3
ACCURACY - Within /- 1 %
VENT / DRAIN - Vent OR Drain holes are provided as per customer’s requirement. Not drilled for Orifice Bore smaller than 25.4 mm.

.

Product Details:

Minimum Order Quantity 1 Piece
Brand FLOWTECH
Size 1-5 inch, 5-10 inch, 10-20 inch, 20-30 inch
Material Standard ASTM A105, ANSI B16.5

DESCRIPTION :

Flowtech Make Orifice Plates & Flange Assemblies.

Suitable for creating differential pressure in a pipe line for flow transmitter etc.

Orifice flange assemblies’ consist of weld neck type flanges with studs, nuts, and gaskets.

Available in SS-316/P.P.Material.
Design standard confirm to BS 1042

FOWTECHmake ORIFICE FLANGE ASSEMBLIES are used for measuring flow of various Liquids, Gases & Steam from

1 ½”to 24” line sizes. It gives an acceptable level of uncertainties at lowest cost and long life without regular maintenances. Orifice Plates are most commonly used as primary element for flow measurement in pipelines based upon the principle of measurement of ‘Differential Pressure’ created when an obstruction is placed in the fluid flow, due to increase in fluid velocity.

Design Standards

DESIGN - Confirming to ISA RP 3.2, DN 1952, BS 1042, ISO-5167
ORIFICE BORE - Confirming to ISO 5167 / BS 1042 / RW Miller / L. K. SPINK / AGE – 3
ACCURACY - Within /- 1 %
VENT / DRAIN - Vent OR Drain holes are provided as per customer’s requirement. Not drilled for Orifice Bore smaller than 25.4 mm.

.

Product Details:

Minimum Order Quantity 1 Piece
Size 2 inch, 3 inch, 2 TO 30 INCH
Brand FLOWTECH

Suitable for creating differential pressure in a pipe line for flow transmitter etc.

Orifice flange assemblies’ consist of weld neck type flanges with studs, nuts, gaskets.

Available in SS-316/P.P.Material.
Design standard confirm to BS 1042.

.

Product Details:

Minimum Order Quantity 1 Piece
Size 2 inch, 3 inch
Brand FLOWTECH

Description:

Flowtech"Make Orifice Plates & Flange Assemblies.

Suitable for creating differential pressure in a pipe line for flow transmitter etc.

Orifice flange assemblies’ consist of weld neck type flanges with studs, nuts, and gaskets.

Available in SS-316/P.P.Material.
Design standard confirm to BS 1042" ""

FOWTECH"make"ORIFICE FLANGE ASSEMBLIES"are used for measuring flow of various Liquids, Gases & Steam from 1 ½”"to 24” line sizes. It gives an acceptable level of uncertainties at lowest cost and long life without regular maintenances. Orifice Plates are most commonly used as primary element for flow measurement in pipelines based upon the principle of measurement of ‘Differential Pressure’ created when an obstruction is placed in the fluid flow, due to increase in fluid velocity.

Design Standards

DESIGN - Confirming to ISA RP 3.2, DN 1952, BS 1042, ISO-5167
ORIFICE BORE - Confirming to ISO 5167 / BS 1042 / RW Miller / L. K. SPINK / AGE – 3
ACCURACY - Within /- 1 %
VENT / DRAIN - Vent OR Drain holes are provided as per customer’s requirement. Not drilled for"" Orifice Bore smaller than 25.4 mm.

.

DESCRIPTION :

Flowtech Make Orifice Plates & Flange Assemblies.

Suitable for creating differential pressure in a pipe line for flow transmitter etc.

Orifice flange assemblies’ consist of weld neck type flanges with studs, nuts, and gaskets.

Available in SS-316/P.P.Material.
Design standard confirm to BS 1042

FOWTECHmake ORIFICE FLANGE ASSEMBLIES are used for measuring flow of various Liquids, Gases & Steam from

1 ½”to 24” line sizes. It gives an acceptable level of uncertainties at lowest cost and long life without regular maintenances. Orifice Plates are most commonly used as primary element for flow measurement in pipelines based upon the principle of measurement of ‘Differential Pressure’ created when an obstruction is placed in the fluid flow, due to increase in fluid velocity.

Design Standards

DESIGN - Confirming to ISA RP 3.2, DN 1952, BS 1042, ISO-5167
ORIFICE BORE - Confirming to ISO 5167 / BS 1042 / RW Miller / L. K. SPINK / AGE – 3
ACCURACY - Within /- 1 %
VENT / DRAIN - Vent OR Drain holes are provided as per customer’s requirement. Not drilled for Orifice Bore smaller than 25.4 mm.
Display Analog

.

Product Details:

Minimum Order Quantity 1 Piece
Brand FLOWTECH
Size 5-10 inch, 5-10 inch, 10-20 inch, 20-30 inch
Material Standard ASTM A105

Description: 
Flowtech Make Orifice Plates & Flange Assemblies.

 Suitable for creating differential pressure in a pipe line for flow transmitter etc.

Orifice flange assemblies’ consist of weld neck type flanges with studs, nuts, and gaskets.

Available in SS-316/P.P.Material.
Design standard confirm to BS 1042 

Flowtech make Orifice flange assemblies are used for measuring flow of various Liquids, Gases & Steam from

1 ½”to 24” line sizes. It gives an acceptable level of uncertainties at lowest cost and long life without regular maintenances. Orifice Plates are most commonly used as primary element for flow measurement in pipelines based upon the principle of measurement of ‘Differential Pressure’ created when an obstruction is placed in the fluid flow, due to increase in fluid velocity.

Design Standards

DESIGN - Confirming to ISA RP 3.2, DN 1952, BS 1042, ISO-5167
ORIFICE BORE - Confirming to ISO 5167 / BS 1042 / RW Miller / L. K. SPINK / AGE – 3
ACCURACY - Within /- 1 %
VENT / DRAIN - Vent OR Drain holes are provided as per customer’s requirement. Not drilled for Orifice Bore smaller than 25.4 mm.

.

Product Details:

Minimum Order Quantity 1 Piece
Brand FLOWTECH
Size 1-5 inch, 5-10 inch, 10-20 inch, 20-30 inch
Material Standard ASTM A105, ANSI B16.5

DESCRIPTION :

Flowtech Make Orifice Plates & Flange Assemblies.

Suitable for creating differential pressure in a pipe line for flow transmitter etc.

Orifice flange assemblies’ consist of weld neck type flanges with studs, nuts, and gaskets.

Available in SS-316/P.P.Material.
Design standard confirm to BS 1042

FOWTECHmake ORIFICE FLANGE ASSEMBLIES are used for measuring flow of various Liquids, Gases & Steam from

1 ½”to 24” line sizes. It gives an acceptable level of uncertainties at lowest cost and long life without regular maintenances. Orifice Plates are most commonly used as primary element for flow measurement in pipelines based upon the principle of measurement of ‘Differential Pressure’ created when an obstruction is placed in the fluid flow, due to increase in fluid velocity.

Design Standards

DESIGN - Confirming to ISA RP 3.2, DN 1952, BS 1042, ISO-5167
ORIFICE BORE - Confirming to ISO 5167 / BS 1042 / RW Miller / L. K. SPINK / AGE – 3
ACCURACY - Within /- 1 %
VENT / DRAIN - Vent OR Drain holes are provided as per customer’s requirement. Not drilled for Orifice Bore smaller than 25.4 mm.

.

Product Details:

Minimum Order Quantity 1 Piece
Brand FLOWTECH
Display Analog

DESCRIPTION :

Flowtech Make Orifice Plates & Flange Assemblies.

 Suitable for creating differential pressure in a pipe line for flow transmitter etc.

Orifice flange assemblies’ consist of weld neck type flanges with studs, nuts, and gaskets.

Available in SS-316/P.P.Material.
Design standard confirm to BS 1042 

FOWTECH make ORIFICE FLANGE ASSEMBLIES are used for measuring flow of various Liquids, Gases & Steam from

1 ½”to 24” line sizes. It gives an acceptable level of uncertainties at lowest cost and long life without regular maintenances. Orifice Plates are most commonly used as primary element for flow measurement in pipelines based upon the principle of measurement of ‘Differential Pressure’ created when an obstruction is placed in the fluid flow, due to increase in fluid velocity.

Design Standards

DESIGN - Confirming to ISA RP 3.2, DN 1952, BS 1042, ISO-5167
ORIFICE BORE - Confirming to ISO 5167 / BS 1042 / RW Miller / L. K. SPINK / AGE – 3
ACCURACY - Within /- 1 %
VENT / DRAIN - Vent OR Drain holes are provided as per customer’s requirement. Not drilled for Orifice Bore smaller than 25.4 mm.

.

Product Details:

Minimum Order Quantity 1 Piece
Brand FLOWTECH
Size 1-5 inch, 5-10 inch, 10-20 inch, 20-30 inch
Material Standard ASTM A105, ANSI B16.5

Description:

Flowtech Make Orifice Plates & Flange Assemblies.
Suitable for creating differential pressure in a pipe line for flow transmitter etc.
Orifice flange assemblies’ consist of weld neck type flanges with studs, nuts, and gaskets.
Available in SS-316/P.P.Material.
Design standard confirm to BS 1042
FOWTECH make Orifice Flange Assembly are used for measuring flow of various Liquids, Gases & Steam from
1 ½”to 24” line sizes. It gives an acceptable level of uncertainties at lowest cost and long life without regular maintenances.
Orifice Plates are most commonly used as primary element for flow measurement in pipelines based upon the principle of measurement of ‘Differential Pressure’ created when an obstruction is placed in the fluid flow, due to increase in fluid velocity.

Design Standards:

Design - Confirming to ISA RP 3.2, DN 1952, BS 1042, ISO-5167
Orifice Bore - Confirming to ISO 5167 / BS 1042 / RW Miller / L. K. SPINK / AGE – 3
Accuracy - Within /- 1 %
Vent / Drain - Vent OR Drain holes are provided as per customer’s requirement. Not drilled for Orifice Bore smaller than 25.4 mm.

.

Product Details:

Size 2 inch, 3 inch, 3 inch, 2 TO 30 INCH, 2 TO 30 INCH
Brand FLOWTECH, FLOWTECH

DESCRIPTION :

Flowtech Make Orifice Plates & Flange Assemblies.

Suitable for creating differential pressure in a pipe line for flow transmitter etc.

Orifice flange assemblies’ consist of weld neck type flanges with studs, nuts, and gaskets.

Available in SS-316/P.P.Material.
Design standard confirm to BS 1042

FOWTECH make ORIFICE FLANGE ASSEMBLIES are used for measuring flow of various Liquids, Gases & Steam from

1 ½” to 24” line sizes. It gives an acceptable level of uncertainties at lowest cost and long life without regular maintenances. Orifice Plates are most commonly used as primary element for flow measurement in pipelines based upon the principle of measurement of ‘Differential Pressure’ created when an obstruction is placed in the fluid flow, due to increase in fluid velocity.

Design Standards

DESIGN - Confirming to ISA RP 3.2, DN 1952, BS 1042, ISO-5167
ORIFICE BORE - Confirming to ISO 5167 / BS 1042 / RW Miller / L. K. SPINK / AGE – 3
ACCURACY - Within /- 1 %
VENT / DRAIN - Vent OR Drain holes are provided as per customer’s requirement. Not drilled for Orifice Bore smaller than 25.4 mm.

.

Product Details:

Minimum Order Quantity 1 Piece
Size 2 inch, 3 inch
Brand FLOWTECH

DESCRIPTION :

Flowtech Make Orifice Plates & Flange Assemblies.

Suitable for creating differential pressure in a pipe line for flow transmitter etc.

Orifice flange assemblies’ consist of weld neck type flanges with studs, nuts, and gaskets.

Available in SS-316/P.P.Material.
Design standard confirm to BS 1042

FOWTECHmake ORIFICE FLANGE ASSEMBLIES are used for measuring flow of various Liquids, Gases & Steam from 1 ½”to 24” line sizes. It gives an acceptable level of uncertainties at lowest cost and long life without regular maintenances. Orifice Plates are most commonly used as primary element for flow measurement in pipelines based upon the principle of measurement of ‘Differential Pressure’ created when an obstruction is placed in the fluid flow, due to increase in fluid velocity.

Design Standards

DESIGN - Confirming to ISA RP 3.2, DN 1952, BS 1042, ISO-5167
ORIFICE BORE - Confirming to ISO 5167 / BS 1042 / RW Miller / L. K. SPINK / AGE – 3
ACCURACY - Within /- 1 %
VENT / DRAIN - Vent OR Drain holes are provided as per customer’s requirement. Not drilled for Orifice Bore smaller than 25.4 mm.

.

Product Details:

Minimum Order Quantity 1 Piece
Brand FLOWTECH, FLOWTECH
Display Analog

DESCRIPTION :

Flowtech Make Orifice Plates & Flange Assemblies.

Suitable for creating differential pressure in a pipe line for flow transmitter etc.

Orifice flange assemblies’ consist of weld neck type flanges with studs, nuts, and gaskets.

Available in SS-316/P.P.Material.
Design standard confirm to BS 1042

FOWTECHmake ORIFICE FLANGE ASSEMBLIES are used for measuring flow of various Liquids, Gases & Steam from

1 ½”to 24” line sizes. It gives an acceptable level of uncertainties at lowest cost and long life without regular maintenances. Orifice Plates are most commonly used as primary element for flow measurement in pipelines based upon the principle of measurement of ‘Differential Pressure’ created when an obstruction is placed in the fluid flow, due to increase in fluid velocity.

Design Standards

DESIGN - Confirming to ISA RP 3.2, DN 1952, BS 1042, ISO-5167
ORIFICE BORE - Confirming to ISO 5167 / BS 1042 / RW Miller / L. K. SPINK / AGE – 3
ACCURACY - Within /- 1 %
VENT / DRAIN - Vent OR Drain holes are provided as per customer’s requirement. Not drilled for Orifice Bore smaller than 25.4 mm.

.

DESCRIPTION :

Flowtech Make Orifice Plates & Flange Assemblies.

Suitable for creating differential pressure in a pipe line for flow transmitter etc.

Orifice flange assemblies’ consist of weld neck type flanges with studs, nuts, and gaskets.

Available in SS-316/P.P.Material.
Design standard confirm to BS 1042

FOWTECH make ORIFICE FLANGE ASSEMBLIES are used for measuring flow of various Liquids, Gases & Steam from

1 ½” to 24” line sizes. It gives an acceptable level of uncertainties at lowest cost and long life without regular maintenances. Orifice Plates are most commonly used as primary element for flow measurement in pipelines based upon the principle of measurement of ‘Differential Pressure’ created when an obstruction is placed in the fluid flow, due to increase in fluid velocity.

Design Standards

DESIGN - Confirming to ISA RP 3.2, DN 1952, BS 1042, ISO-5167
ORIFICE BORE - Confirming to ISO 5167 / BS 1042 / RW Miller / L. K. SPINK / AGE – 3
ACCURACY - Within /- 1 %
VENT / DRAIN - Vent OR Drain holes are provided as per customer’s requirement. Not drilled for Orifice Bore smaller than 25.4 mm.

.

Product Details:

Minimum Order Quantity 1 Piece
Brand FLOWTECH, FLOWTECH
Size 1-5 inch, 5-10 inch, 10-20 inch
Material Standard ANSI B16.5, ANSI B16.5

DESCRIPTION :

Flowtech Make Orifice Plates & Flange Assemblies.

Suitable for creating differential pressure in a pipe line for flow transmitter etc.

Orifice flange assemblies’ consist of weld neck type flanges with studs, nuts, and gaskets.

Available in SS-316/P.P.Material.
Design standard confirm to BS 1042

FOWTECHmake ORIFICE FLANGE ASSEMBLIES are used for measuring flow of various Liquids, Gases & Steam from 1 ½”to 24” line sizes. It gives an acceptable level of uncertainties at lowest cost and long life without regular maintenances. Orifice Plates are most commonly used as primary element for flow measurement in pipelines based upon the principle of measurement of ‘Differential Pressure’ created when an obstruction is placed in the fluid flow, due to increase in fluid velocity.

Design Standards

DESIGN - Confirming to ISA RP 3.2, DN 1952, BS 1042, ISO-5167
ORIFICE BORE - Confirming to ISO 5167 / BS 1042 / RW Miller / L. K. SPINK / AGE – 3
ACCURACY - Within /- 1 %
VENT / DRAIN - Vent OR Drain holes are provided as per customer’s requirement. Not drilled for Orifice Bore smaller than 25.4 mm.

.

Product Details:

Minimum Order Quantity 1 Piece
Brand FLOWTECH
Display Analog

DESCRIPTION :

Flowtech Make Orifice Plates & Flange Assemblies.

Suitable for creating differential pressure in a pipe line for flow transmitter etc.

Orifice flange assemblies’ consist of weld neck type flanges with studs, nuts, and gaskets.

Available in SS-316/P.P.Material.
Design standard confirm to BS 1042

FOWTECH make ORIFICE FLANGE ASSEMBLIES are used for measuring flow of various Liquids, Gases & Steam from

1 ½” to 24” line sizes. It gives an acceptable level of uncertainties at lowest cost and long life without regular maintenances. Orifice Plates are most commonly used as primary element for flow measurement in pipelines based upon the principle of measurement of ‘Differential Pressure’ created when an obstruction is placed in the fluid flow, due to increase in fluid velocity.

Design Standards

DESIGN - Confirming to ISA RP 3.2, DN 1952, BS 1042, ISO-5167
ORIFICE BORE - Confirming to ISO 5167 / BS 1042 / RW Miller / L. K. SPINK / AGE – 3
ACCURACY - Within /- 1 %
VENT / DRAIN - Vent OR Drain holes are provided as per customer’s requirement. Not drilled for Orifice Bore smaller than 25.4 mm.

.

DESCRIPTION :

Flowtech Make Orifice Plates & Flange Assemblies.

Suitable for creating differential pressure in a pipe line for flow transmitter etc.

Orifice flange assemblies’ consist of weld neck type flanges with studs, nuts, and gaskets.

Available in SS-316/P.P.Material.
Design standard confirm to BS 1042

FOWTECHmake ORIFICE FLANGE ASSEMBLIES are used for measuring flow of various Liquids, Gases & Steam from

1 ½”to 24” line sizes. It gives an acceptable level of uncertainties at lowest cost and long life without regular maintenances. Orifice Plates are most commonly used as primary element for flow measurement in pipelines based upon the principle of measurement of ‘Differential Pressure’ created when an obstruction is placed in the fluid flow, due to increase in fluid velocity.

Design Standards

DESIGN - Confirming to ISA RP 3.2, DN 1952, BS 1042, ISO-5167
ORIFICE BORE - Confirming to ISO 5167 / BS 1042 / RW Miller / L. K. SPINK / AGE – 3
ACCURACY - Within /- 1 %
VENT / DRAIN - Vent OR Drain holes are provided as per customer’s requirement. Not drilled for Orifice Bore smaller than 25.4 mm.

.

Product Details:

Minimum Order Quantity 1 Piece
Material SS
Brand FLOWTECH, FLOWTECH
Display Analog

Description : 

Flowtech Make Orifice Plates & Flange Assemblies.

Suitable for creating differential pressure in a pipe line for flow transmitter etc.

Orifice flange assemblies’ consist of weld neck type flanges with studs, nuts, and gaskets.

Available in SS-316/P.P.Material.
Design standard confirm to BS 1042

Fowtech Make Orifice Flange Assemblies Are Used For Measuring Flow Of Various Liquids, Gases & Steam From

1 ½”to 24” line sizes. It gives an acceptable level of uncertainties at lowest cost and long life without regular maintenances. Orifice Plates are most commonly used as primary element for flow measurement in pipelines based upon the principle of measurement of ‘Differential Pressure’ created when an obstruction is placed in the fluid flow, due to increase in fluid velocity.

Design Standards

DESIGN - Confirming to ISA RP 3.2, DN 1952, BS 1042, ISO-5167
ORIFICE BORE - Confirming to ISO 5167 / BS 1042 / RW Miller / L. K. SPINK / AGE – 3
ACCURACY - Within /- 1 %
VENT / DRAIN - Vent OR Drain holes are provided as per customer’s requirement. Not drilled for Orifice Bore smaller than 25.4 mm.

.

Applications:

Scientific laboratory
Research centres
Chemical industries

Specifications:

Available in SS-316/P.P. Material
1 ½” to 24” line sizes
Design - confirming to isa rp 3. 2, dn 1952, bs 1042, iso-5167
Orifice bore - confirming to iso 5167 / bs 1042 / rw miller / l. K. Spink / age – 3
Accuracy - within /- 1 %
Vent / drain - vent or drain holes are provided as per customer’s requirement. Not drilled for orifice bore smaller than 25. 4 mm

.

Design Standards:

Design- Confirming to ISA RP 3.2, DN 1952, BS 1042, ISO-5167
Orifice Bore- Confirming to ISO 5167 / BS 1042 / RW Miller / L. K. SPINK / AGE – 3
Accuracy - Within /- 1 %
VENT / DRAIN - Vent OR Drain holes are provided as per customer’s requirement. Not drilled for Orifice Bore smaller than 25.4 mm.

.

FOWTECHmake Orifice Plates and Flange Assemblies are used for measuring flow of various Liquids, Gases & Steam from 1 ½”to 24” line sizes. It gives an acceptable level of uncertainties at lowest cost and long life without regular maintenances. Orifice Plates are most commonly used as primary element for flow measurement in pipelines based upon the principle of measurement of ‘Differential Pressure’ created when an obstruction is placed in the fluid flow, due to increase in fluid velocity.

Design Standards:

Design- Confirming to ISA RP 3.2, DN 1952, BS 1042, ISO-5167
Orifice Bore- Confirming to ISO 5167 / BS 1042 / RW Miller / L. K. SPINK / AGE – 3
Accuracy - Within /- 1 %
VENT / DRAIN - Vent OR Drain holes are provided as per customer’s requirement. Not drilled for Orifice Bore smaller than 25.4 mm.

.

Product Details:

Size 2 inch, 3 inch
Brand FLOWTECH

Flowtech make Orifice Plates and Flange Assembly are used for measuring flow of various Liquids, Gases & Steam from 1 ½” to 24” line sizes. It gives an acceptable level of uncertainties at lowest cost and long life without regular maintenances. Orifice Plates are most commonly used as primary element for flow measurement in pipelines based upon the principle of measurement of ‘Differential Pressure’ created when an obstruction is placed in the fluid flow, due to increase in fluid velocity.

Flowtech Make Orifice Plates & Flange Assemblies.
Suitable for creating differential pressure in a pipe line for flow transmitter etc.
Orifice flange assemblies’ consist of weld neck type flanges with studs, nuts, and gaskets.
Available in SS-316/ P.P. Material.
Design standard confirm to BS 1042
Design Standards
Design - Confirming to ISA RP 3.2, DN 1952, BS 1042, ISO-5167
Orifice Bo re - Confirming to ISO 5167 / BS 1042 / RW Miller / L. K. SPINK / AGE – 3
Accuracy - Within /- 1 %
VENT / DRAIN - Vent OR Drain holes are provided as per customer’s requirement. Not drilled for Orifice Bore smaller than 25.4 mm.

.

Product Details:

Brand Flowtech
Usage Industrial, Domestic

Specifications: 

Size : 50 to 600 NB.
Round, Square & Rectangular Shape.
MOC : CS, SS-304, SS-316.

.

Product Details:

Minimum Order Quantity 1 Piece
Brand FLOWTECH
Display Analog

DESCRIPTION :

Flowtech Make Orifice Plates & Flange Assemblies.

 Suitable for creating differential pressure in a pipe line for flow transmitter etc.

Orifice flange assemblies’ consist of weld neck type flanges with studs, nuts, and gaskets.

Available in SS-316/P.P.Material.
Design standard confirm to BS 1042 

FOWTECH make ORIFICE FLANGE ASSEMBLIES are used for measuring flow of various Liquids, Gases & Steam from

1 ½” to 24” line sizes. It gives an acceptable level of uncertainties at lowest cost and long life without regular maintenances. Orifice Plates are most commonly used as primary element for flow measurement in pipelines based upon the principle of measurement of ‘Differential Pressure’ created when an obstruction is placed in the fluid flow, due to increase in fluid velocity.

Design Standards

DESIGN - Confirming to ISA RP 3.2, DN 1952, BS 1042, ISO-5167
ORIFICE BORE - Confirming to ISO 5167 / BS 1042 / RW Miller / L. K. SPINK / AGE – 3
ACCURACY - Within /- 1 %
VENT / DRAIN - Vent OR Drain holes are provided as per customer’s requirement. Not drilled for Orifice Bore smaller than 25.4 mm.

.