Types of Gratings:

1. Open gratings

2. Covered on one side: Panel shown below in the drawing shall be covered on one side with surface finish of your choice (types of surfaces finishes available are mentioned below)

Surface Finish available:

The types of surface finishes mentioned below are used for making gratings non slippery i.e. anti skid

1. Completely granular surface (possible in case of both open and covered gratings)

2. Chequered Surface (possible in case of only covered gratings). Surface appearance shall be similar as that in MS chequered plates.

Types of Resin Systems:

1. Isothalic Resin System

2. G P Vinyl Ester Resin System: This is used for higher chemical resistance

3. Bisphenol Resin System: This is also used for higher chemical resistance

Color:

Grey, Red, Yellow and Green

Other colors to order

Specification:-

TYPE - I

Panel size: 1m x 1m

Clear Opening /Mesh size: 30mmX30mm square mesh

Depth : 20 mm, 25mm & 30mm

Rib Bar thickness: 8mm X 10mm

Bar thickness 20 mm at corners 20mm at centre and corner

Weight : 16kg, 18kg & 21kg respectively.

Load Carrying: 2 Ton, 4 Ton & 6 Ton for 2 parallel edges supported at maximum 1 m span for loads of

2000 Kgs per sqm UDL, 4000 Kgs per sqm UDL & 6000 Kgs per sqm UDL respectively.

TYPE - II

Panel size: 1m x 1m

Clear Opening /Mesh size: 38mmX38mm square mesh

Depth : 20 mm, 25mm & 30mm

Rib Bar thickness: 6mm X 8mm

Bar thickness 20 mm at corners.

Weight : 14kg, 16kg & 19kg respectively

Load Carrying: 500 Kg, 900 Kg & 1.3 T for 2 parallel edges supported at maximum 1 m span for loads of

500 Kgs per sqm UDL, 900 Kgs per sqm UDL & 1.3 T per sqm UDL respectively. 

These Laboratory Fume Hood are used in different applications like laboratories, research units of industries, institution etc. They are also used in industrial applications or other activities where hazardous or noxious vapors, gases or dusts are generated or released. These hoods are known for their features like non-conductive, chemical resistant, corrosion proof, precision design, accurate functioning.

1. Fabricated out of 3mm thick PVC /Polypropylene /FRP sheet as your requirements and designs
2. Good mechanical Strength Durable replaces mild steel Stainless Steel MSRL etc
3. Economical in cost
4. No effect of corrosion fumes, acids and alkaline fumes
5. No Expenditure on periodic painting jobs
6. Chimney prevents corrosive and dangerous fumes from spreading
7. Laboratory fume cupboards are provided with PVC/polypropylene befalls for suction at three places
8. Laboratory Table Top bonded lining with polypropylene sheets, PPE elliptical  and round table drains are provided

These PP, PVC, PVDF, FRP Ducting & Hoods are available as per the international quality standards and can be customized as per the specifications provided by the customers. These are available to our clients at normal prices. These are tested with various parameters and ensures before sending it to the clients. These hoods offer high durability and efficient functionality.

1. Polypropylene Scrubbers and Tower Packing for SO2, SO3, NO2, CL2, CO2, NH3HCL, HF and BR, Gases And Corrosive Gases With exhaust System
2.  
3. We design fabricate, install and commission at site Scrubber made of PP + FRP, PVC + FRP an only FRP in various diameters and heights
4. Highly resistance to corrosion and temperature resistance upto 120 deg C
5. No question of air pollution
6. Packed with Polypropylene pall ring and intalox saddle tower, packing.
7. Very useful for SO2, SO3, HCL, HNO3, HF, CL2, BR, Gases absorption and stripping, with alkalies and water to neutralize and to make acids
8. Air washing, Fume Scrubbing, Dehydrating, Decarbonating and Depreciating
9. CO2 absorption by MEA or hot carbonate process

These Polypropylene, PVC, FRP Scrubber are widely used by our clients and can be customized as per the specifications provided by the customers. These are known for their features like Fabricated from high quality polypropylene, Reinforced, Capability to withstand sufficient negative pressure. These are quality products and available at normal prices.

These Poly Trays for Dryers are available to our clients in different shapes and sizes. These dryers are used in various applications like chemicals, pharmaceuticals, dyes, intermediates and food products industries. These are appreciated by our client’s for their silent features like durable, innovative design, high purity polypropylene, resistant to acids, alkalis and corrosive chemical, temperature resistant upto 1100c etc.

These FRP Scrubbers are used to limit the exposure of gas and fumes. These scrubbers are having silent features like High scrubbing efficiency, minimizes total packing depth required, customized sizes, made of qualitative materials. These scrubbers are fabricated as per the specifications provided by the customers.

• Fabricated out of 3mm and 5 mm thick PVC / FRP/ Polypropylene sheets as per your requirements and externally coated with FRP to give good mechanical strength.
• 1/2” thick Flanges are used at required places by using Flexible PVC Gaskets and polypropylene and bolts.
• Highly resistant to acids, alkalies and other Corrosive gases, and temperature resistance upto 1200C.
• Non contaminating, surface is smooth so less abrasion resistance to fumes Velocity long lasting and durable.
• Very useful for Fine Chemicals, Dycs, Pharmaceutical and pickling plants, Electroplating plants, phosphatase Tanks, Laboratory Fume Cupboards and Process Rooms

• Centrifugal exhaust fans, blowers are corrosion-resistance as they have been manufactured through from rigid PVC/ Polypropylene + FRP
• Imparts special properties of ″weathering” corrosive fumes and moist gases
• Available in various sizes from 500 cfm to 10,000 cfm capacity
• Impeller is one piece, injection moulded dynamically balanced trouble free and long lasting, directly OR indirectly coupled with electric motor/Flame proof motors
• Very useful for laboratory fume cupboard, Pickling plants Electroplating industries, reaction vessels, process rooms for Corrosive, hazardous fumes removal and Scrubbers
• Protecting the health of workmen and ensuring increase in production
• polypropylene moulded impeller available in various sizes 10”, 12½”, 17” and 24” dia for PP exhaust fans.
• FRP fan upto 35,000 CFM capacity & all fans are tested as per ISI Specification No IS 4894-1968 for capacity and W.G Pressure.

• Polypropylene/PVC exhaust systems for laboratory fume cupboards
• Fabricated out of 3mm thick PVC /Polypropylene /FRP as your requirements and designs
• Good mechanical Strength Durable replaces mild steel Stainless Steel MSRL etc
• Economical in cost
• No effect of corrosion fumes, acids and alkaline fumes
• No Expenditure on periodic painting jobs
• Chimney prevents corrosive and dangerous fumes from spreading
• Laboratory fume cupboards are provided with PVC/polypropylene befalls for suction at three places
• Laboratory Table Top bonded lining with polypropylene sheets, PPE elliptical and round table drains are provided

• Fabricated out of 3mm & 5mm thick PVC /FRP/ Polypropylene sheets as per client requirements & externally coated with FRP to give good mechanical strength.
• 1/2” thick flanges are used at required places by using Flexible PVC Gaskets & PP Nuts & bolts.
• Highly resistance to acids, alkalies & other Corrosive gases & temperature resistance up to 120 degree Celsius.
• Very useful for fine chemicals, dyes, pharmaceuticals & Pickling Plants, Phosphatase tanks, Lab fume-cupboard & process rooms.

These strainers are used for filtration application in pressure sand filter, carbon filter, softener etc. The moc of strainers are made out of pp which is suitable for drinking water application and resist corrosion having good mechanical strength also these strainers can be made out in different grade of material based on client's application.

These strainers are installed on strainer as plate design and header lateral system for distribution & collection purpose. These strainers are providing very good flow rate and by which it improves the backwash and filtration efficiency of the plant.

The PP FRP Ducting will be fabricated out of PP Sheets & the same will be externally coated with FRP using Isopthalic grade resin (Suitable for Highly Corrosive atmosphere) along with 450Gm/cc Chopped strande mate. , These ducts offer long service life and effective functioning.PP FRP Ducting are appreciated for features such as corrosion resistant, long lasting, leak proof and low maintenance. these are available in different shapes and sizes as per the requirements of clients.

This MS Tank Lined with PPGL(Polypropylene glass line) from inside. Bonding done by FRP (fiber reinforced plastic) which is sandwiched in between PPGL and MS. While lining MS Tanks/Vessels all welding work is always tested by spark tester.

PP Ducting is molded from Pure virgin Poly propylene material .Our PP Ducts are appreciated for features such as corrosion resistant, long lasting, leak proof and low maintenance. these are available in different shapes and sizes as per the requirements of clients.

The Ducting will be fabricated out of PVC Sheets & the same will be externally coated with FRP using Isopthalic grade resin(Suitable for Highly Corrosive atmosphere) along with 450Gm/cc Chopped standard mate. , these ducts offer long service life and effective functioning.PP/FRP Ducting are appreciated for features such as corrosion resistant, long lasting, leak proof and low maintenance. these are available in different shapes and sizes as per the requirements of clients.

FRP Ducts offered by us are appreciated for features such as corrosion resistant, long lasting, leak proof and low maintenance. Tested for leakage, these ducts offer long service life and effective functioning. These ducts are light in weight and have superior acoustical qualities making them compatible and versatile for the different industry. Further, these are available in different shapes and sizes as per the requirements of clients.

PVC Ducting is molded from Pure virgin Polyvinyl Chloride material .Our PVC Ducts are appreciated for features such as corrosion resistant, long lasting, leak proof and low maintenance. these are available in different shapes and sizes as per the requirements of clients.

Plastic Fabricators manufacture FRP Pultruded Sections are indeed the most advanced types of sections with excellent corrosion resistivity, high strength and light weight features. All the traditional materials like steel, aluminum & wood that were used to manufacture these sections had their own disadvantages in the industry and eventually FRP Pultruded sections came into picture with virtually maintenance free services. These FRP pultruded sections are the most eco friendly sections available in market as these emit less greenhouse gases and consume less power in comparison to other sections. We have all the expertise to manufacture varied pultruded sections with different specifications to meet diverse industrial requirements.

• We design fabricate, install & commission at site Wet Scrubber made of PP FRP, PVC FRP in various Diameter & heights
• Its highly resistance to Corrosion & temperature resistance up to 100deg.C
• It is packed with tower packing for increasing Scrubbing Efficiency
• It is Very useful for Acidic fume SO2, SO3, HCL,HNO3 & NOx gases absorption & stripping, with alkaline & water to neutralize & to make acid.

Our company is known for expertise in superior range of FRP Linings & coating which have been made using the best raw materials available and using the best technology available in the market for lining to MS Tanks and Civil Trenches and Pits. These products have been priced at very reasonable rates in the market and they are high on demand in the market. These products offer

• High Durabilty
• Long Lasting
• Tested by industries Key Companies

FRP Gratings are widely used in Highly corrosive environment & areas exposed to acids ,alkalis, chemicals, oils etc for following structures, replacing wood & steel almost completely. Our Gratings are Fire Retardant.

We manufacture wide range of Fiberglass Grating surface finishes, colors & panel Sizes.

Types of Gratings:

1. Open gratings

2. Covered on one side

The FRP Garden Bench Patti is made on a Fully Automatic machine by the process of Pultrusion Which is widely used by Bench manufacturers. It has a Wooden finish on it which resembles Wooden Sections. The FRP Park Bench Patti is UV stabilised so that it does not fade in Sun Light.

• Self Supporting tanks made of PP FRP embedded Mild-steel Structure for storage of Corrosive Chemicals. Capacity 200 liters to 1,50,000 Liters.
• PP FRP, PVC FRP Reaction Vessel with P.P / PVC Agitator Capacity 200 Liters to 20,000 Liters .
• Highly durable range of PP FRP Tanks
• PP Rectangular Tanks, FRP Rectangular Tanks & pp frp pickling tank
• FRP tanks for Chemical storage like HCL & sulfuric Acid etc.
• Spark & Leakages Tested for Tanks

PP/RIGID PVC/ FRP Ducting& Canopy Hoods with Damper

1. Ducting is fabricated out of 3mm & 5mm thick PP, PVC sheet as per requirements & externally coated with FRP to give good mechanical strength.

2. Highly resistant to acids ,alkalis & other corrosive gases & temperature resistance up to 110°C.

• Corrosion Resistance
• Long Lasting
• Leak Proof

• We offer PP, PVC, PVDF, FRP Blowers available in dif-ferent sizes and also used in different applications like chemical and pharmaceutical industries, bulk drugs, intermediates, organic chemicals & plating, anodizing industries. They are acknowledged for their features like effective, smooth and energy efficient functioning and resistance to corrosion.
• Protecting the health of workmen and ensuring increase in production.
• Direct Drive Blowers are used for exhaust of Fumes from Laboratory Fume Hood.
• Impellers which are used in blowers are One Piece Molded in various sizes 10”, 12.5” , 17”, 24” Diameter
• Blowers are made up to 35,000 CFM capacity & tested as per ISI specification No. IS 4894-1968 FOR Capacity and W.G. Pressure .

• InDirect Drive Blowers are used for exhaust of Fumes from Laboratory Fume Hood.
• Impellers which are used in blowers are One Piece Molded in various sizes 10”, 12.5” , 17”, 24” Diameter
• Impeller which used are one piece injection molded & Dynamically balanced to give accurate CFM.

It is used for highly Corrosive Chemicals for various range of Temperature ,with high Stability & Rigidity .Baffles are provided for generating turbulence in the tank . Agitator can be made of MS with PP Lining with gearbox motor arrangement.

PP impeller is injection molded one piece statically & dynamically balanced. Impellers are available in Different Capacities & pressures :

Sizes: 10”,12.5” ,15.5”,17” & 24”.

• Made from Virgin PP
• Highly Durable

It is the most efficient types of ring packing for large scale superior characteristic derive from the slotted wall & the internal projecting tongues, which give this higher capacity or lower pressure drop also higher contact efficiency arising from the better disposition. And better wetting of the surface Migration of liquid forward of the vessel wall is also reduced.

• Our Cupsinks are manufacture from virgin Polypropylene in Black Color.
• It is mostly used for Laboratory purpose in Fumehoods & Lab Furnture.
• Highly Resistant to All Chemicals & Good mechanical Strength.

• Our Scrapper /Spatulas & Scoop are manufacture from Virgin Polypropylene & having good mechanical strength & unbreakable handle.
• It is widely used in Chemical ,Pharmaceutical, fine chemicals , API, Drug Intermediates, Dyes,etc.
• Highly Durable
• Economical in cost

We offer high quality PP Grid Vacuum Belt Filters that are made using quality raw materials. It is widely used in Oil, Chemical, Pharmaceutical & Food industries as filters & Screens. These are woven with best quality PP & exhibit features like:

• Resistant to Corrosion
• Acid & Heat Resistant

These Strainers are used for Filtration application in pressure sand filter , carbon filter, softeners etc. The MOC of Strainer are made out of PP which is suitable for drinking water application & Resist corrosion having good mechanical strength also these strainers can be made out in different grade of material based on Clients application.

These Strainers are installed on strainer as plate design & Header lateral system for distribution & collection purpose. These Strainers are providing very good flow rate & by which it improves the backwash & filtration efficiency of the Plant. Slit size of strainer is 0.2mm

PP Balls are manufactured from virgin Polypropylene .It is mostly used to recover evaporation and heat loss in electroplating Industries. It is highly resistant to Chemicals, having good mechanical strength.

Our pultruded gratings are manufactured and intended for utilization in an extensive variety of modern applications that oblige quality and corrosion resistance.

Applications

Walkways | Platforms | Trench covers | Staircase | Floorings | Foot Bridges | Swimming pool overflow | Fencing | Elevated car parking | Step Treads | Earth pit covers

Industry

Chemical | Food & Beverage | Marine | Oil & Gas | Power | Industry | Buildings | Constructions | Pharmaceuticals | Pulp & Paper | Recreation | Water & Waste Treatment | Shipping | Transportation | Architectural | Telecommunications.

Size: 25mm Thickness & 38 mm Thickness

PLASTIC FABRICATORS are one the major epoxy and frp lining specialist from India. Epoxy has an advantage over other corrosion resistant lining material, because it can be filled into very narrow fissures crevices angles etc to provide protection against corrosion. it can also be applied in various thicknesses to fill up the imperfection of the substrata. Epoxy Lining like A.R Brick lining can be directly applied to the masonry work or to the metal surface. 
Years of experience in anti corrosion lining work gives us the confidence to assure you unmatched type and prompt delivery at reasonable rates. To achieve this we have with us a team of highly skilled workmen in each of the abovementioned categories, overseen by qualified and experienced supervisory staff . There are different grades of Epoxy with varying Bond Strength etc.

Description / Specification of Frp Coating We are involved in offering a wide range of Frp Coating to our most valued clients. Our range of these are widely appreciated by our clients which are situated all round the nation. We offer our range of it at most affordable prices. We introduce ourselves as an eminent trader and supplier of an extensive array of  Frp Coating. Prior to dispatch, our quality controllers run numerous tests on the entire range on various parameters of quality and durability. The offered equipment is manufactured using superior quality components with the aid of sophisticated techniques at the vendors' end. Moreover, our precious clients can purchase it in different technical specifications at reasonable price from us within promised time frame. Features: Sturdy design Highly durable Application specific design

Our company is well known in the market for the manufacture and the export of a superior range of FRP Linings which have been made using the best raw materials available in the market and these products have been made using the best technology available in the market. These products have been priced at very reasonable rates in the market and they are high on demand in the market. These products offer a high performance and they offer a long lasting service life.

Features –

High quality
Durable
Efficient performance

1. We design fabricate, install & commission at site Scrubber made of PP + FRP, PVC FRP in various Diameter & heights
2. Its highly resistance to Corrosion & temperature resistance up to 120deg.C
3. It is packed with tower packing for increasing Scrubbing Efficiency
4. It is Very useful for SO2, SO3, HCL,HNO3 gases absorption & stripping, with alkaline & water to neutralize & to make acids

These PP, FRP, PVC Reaction Vessels & Storage Tanks are available in different shapes, sizes and with a capacity of 100kl/100 tons. These are found in various applications like chemical, bulk drugs, intermediates, electroplating etc. These are recognized for their features like Durable, different colors, leak proof/tested welding joints, dimensional stability, long service life.

1. Rigid PVC/ propylene bonded linings to mild steel tanks etc in 3mm and 5mm thickness
2. Polypropylene FRP and only FRP lining to M.S and Wooden Tanks for storage of Corrosive Chemicals
3. Self Supporting tanks made of PVC + FRP and Polypropylene + FRP em boding Mild-steel structure for storage of Corrosive Chemicals. Capacity 200 liters to 10,000 Liters
4. Self supporting tanks moulded in FRP upto 10 tons capacity
5. Polypropylene- FRP Reaction Vessel with P.P Stirrer Capacity 200 Liters to 10,000 Liters

1. Rigid PVC/ propylene bonded linings to mild steel tanks etc in 3mm and 5mm thickness
2. Polypropylene FRP and only FRP lining to M.S and Wooden Tanks for storage of Corrosive Chemicals
3. Self Supporting tanks made of PVC + FRP and Polypropylene + FRP em boding Mild-steel structure for storage of Corrosive Chemicals. Capacity 200 liters to 10,000 Liters
4. Self supporting tanks moulded in FRP upto 60 tons capacity
5. Polypropylene- FRP Reaction Vessel with P.P Stirer Capacity 200 Liters to 60,000 Liters

Description / Specification of Frp Storage Tanks We are involved in offering a wide range of Frp Storage Tanks to our most valued clients. Our range of these are widely appreciated by our clients which are situated all round the nation. We offer our range of it at most affordable prices. We introduce ourselves as an eminent trader and supplier of an extensive array of  Frp Storage Tanks. Prior to dispatch, our quality controllers run numerous tests on the entire range on various parameters of quality and durability. The offered equipment is manufactured using superior quality components with the aid of sophisticated techniques at the vendors' end. Moreover, our precious clients can purchase it in different technical specifications at reasonable price from us within promised time frame. Features: Sturdy design Highly durable Application specific design

1. Reaction vessel for corrosive chemicals
2. Rigid PVC/ propylene bonded linings to Mild steel tanks etc in 3mm and 5mm thickness
3. Polypropylene FRP and only FRP lining to M.S and Wooden Tanks for storage of Corrosive Chemicals
4. Self Supporting tanks made of PVC + FRP and Polypropylene + FRP em boding Mild-steel structure for storage of Corrosive Chemicals. Capacity 200 liters to 10,000 Liters
5. Self supporting tanks moulded in FRP upto 10 tons capacity
6. Polypropylene- FRP Reaction Vessel with P.P Stirrer Capacity 200 Liters to 10,000 Liters

These Polypropylene, PVC, FRP Scrubber are widely used by our clients and can be customized as per the specifications provided by the customers. These are known for their features like Fabricated from high quality polypropylene, Reinforced, Capability to withstand sufficient negative pressure. These are quality products and available at normal prices.

These PP Filter Nozzles are used generally used for water treatment plants. These are recognized for their features such as made from grade polypropylene, encased body-cover point gasket, highly durable, technically superior. These are available in different shapes and sizes and can be availed to our clients at affordable prices.

These PP Tower Packings /Scrubber are designed and developed using best quality materials and widely used by our clients for their unique features. These are available as per the specifications provided by the customers. These are resistance to various acids like hydrochloric acid and sulfuric acid. These are available to our clients at affordable prices.

We offer PP, PVC, PVDF, FRP Blowers are available in different sizes and also used in different applications like chemical and pharmaceutical industries, bulk drugs, intermediates, organic chemicals & plating, anodizing industries. They are acknowledging for their features like effective and smooth function bowering, resistance to corrosion, efficient impellers.

It is the most efficient types of ring packing for large scale superior characteristic derive from the slotted wall and the internal projecting tongues, which give this higher capacity or lower pressure drop, also higher contact efficiency arising from the better disposition. And better wetting of the surface Migration of liquid forward of the vessel wall is also reduced. The free gas space is much this same as for plain rings

Polypropylene Plastic intalox saddles are a highly effective packing for use in most fume removal applications. A typical Scrubbing is shown here in schematic form. The polluted air or gas steam is drawn through a bed of wetted plastic intalox saddles which provides very large surface area contact promoting rapid absorption of pollutants into the liquid stream. Contaminant removal efficiency of 99% are possible at relatively low liquid flow rates. Size available 1”, 1.5”, 2”, 3”, and 3.5” dia

It is the most efficient types of ring packing for large scale superior characteristic derive from the slotted wall & the internal projecting tongues, which gives the higher capacity or lower Pressure drop, also higher contact efficiency arising from the better disposition & better wetting of the surface migration of liquid forward the vessel wall is also reduced The free gas space is much this same as for plain ring.

Poly trays made of engineering plastic materials for dryer with improved mechanical strength temperature resistance upto 140 deg. C and working with load at 110 deg. C. Injection moulded one piece highly resistance to corrosion.

• It is moulded by using ISOTHELIC resin & FRP TRAYS moulded by using BISPHENOL resin
• Size 32”L x 16”W x 1.25” Height
• Complete FRP Tray dryer for steam heating. FRP lining from inside to dryers and trolly to prevent corrosion
• Polypropylene ducting and exhaust fans for dryer to remove corrosive fumes from outlet of dryers

It is manufactured through from PVC/Polypropylene sheet with moulded polypropylene impeller of Size 10” / 12 ½” 17” and 24” diameter, capacity 700, 1000, 2000, 5000, 7500 and 10.000 CFM only FRP moulded fans upto 35,000 CFM capacity and all fans tested as per ISI specification No. I.S.4894-1968 for capacity and WG pressure.

Polypropylene PVC and FRP hoods and ducting in various sizes with damper 90 Deg & 45 Deg long radius bend Tee & reducers and moulded flanges fitted with polypropylene nuts and blots and flexible PVC gaskets for Laboratory fume-cupboard, reaction vessels, plating, anodizing , galvanizing, pickling plants and scrubbers etc

We offer our clients Tanks and Tank lining, Self Supporting Tanks and Reaction Vessels. These are mader from best quality raw material and by using latest technology.

In PVC polypropylene and FRP from 200 ltrs to 25,000 Ltrs Capacity.

For HCL,SO2,SO3,CL2,NO2, and HF,CL2, & BR2, gas scrubbing with polypropylene tower packing like pall rings made of LTHA grade for higher Temperature and Corrosion Resistance Size ½”,1”,½”,2”,3½ ”, etc, intalox Saddles Size 2” and 3”

P. P valves, single & double decker strainer buttons, pipe works, PVC dionise columns polypropylene pall ring for tower packing and polypropylene level gauge indicators.

One piece molded specially designed for industrial use with good mechanical strength and long lasting for powder and cake transfer from bags etc

For industrial, Automobile, Textile, Electronic and Rayon industries etc.

The fan casing will be fabricated out of 3mm thick PVC sheets and the same will be Externally coated with 5mm thick FRP with drain arrangement at the bottom, The inlet & Outlet will be ½” drilled for connections. The Impeller is injection moulded one piece statically and dynamically balanced in polypropylene indirectly coupled with 3 Phase motor. The fan will be tested as per IS 4894-1968

Indirectly driven Exhaust fan will have imported NTN self aligning sleeve bearing in plumber block, V belt driven with pulleys mounted on M.S Stand, with corrosion-resistance coating. PP Moulded impellers are available in various sizes 10” 121/2” 15” 17” & 24”.

These PP Hood, Ducts with Blower & Chimney  are made using pure quality PVC, PVDF and FRP materials and highly used by our clients. These are used in different applications like pharmaceutical and chemical industries. These are known for their features like highly durable, different shapes and sizes, energy-efficient, customized from, long service life.

• This trays are molded one piece with high mechanical strength it is very useful for drying & crystallization
• Resistance to acids, alkalies & Corrosive Chemicals
• These trays are manufactured from virgin Polypropylene material having good mechanical strength & it does not sag
• in this tray there is no chances of contamination, material do not stick on its surface therefore no loss of material
• Its temperature resistance up to 120 deg C
• It has smooth surface & its is easy to clean & also it is washable with water
• Size 32” length X 16” width x 1.25” Height with 5 mm wall thickness

• Our cup sinks are manufacture from virgin polypropylene in Black color
• It is mostly used for Laboratory purpose in fume hoods & lab furniture
• It is highly resistance to Chemical & good mechanical strength

• Our Scrappers/Spatulas & Scoop are manufacture from virgin polypropylene & having good mechanical strength & unbreakable handle.
• It is widely used in Chemical & Pharmaceutical Industries

These strainers are used for filtration application in pressure sand filter, carbon filter, softener etc. The moc of strainers are made out of pp which is suitable for drinking water application and resist corrosion having good mechanical strength also these strainers can be made out in different grade of material based on client's application. These strainers are installed on strainer as plate design and header lateral system for distribution & collection purpose. These strainers are providing very good flow rate and by which it improves the backwash and filtration efficiency of the plant.

This Micron Filtration Plant are widely used by our clients and appreciated for their features like Consistent performance, Easy unit assembly, Facilitates continuous filtration, SC Low maintenance. These are available to our clients with accurate dimensions and offers high durability. These are available at affordable prices to our customers.

These PP Grids for Vacuum Belt Filter are made using high grade quality materials and highly appreciated by pour clients for their unique features. These are identified for their features like Resistant to corrosion, Acid and heat resistant. These filters are used in different applications like oil, chemical, pharmaceutical and food industries as filters and screens.