RVT-2 is two-component room temperature silicone. Depending on its curing mechanism, two type of RVT-2 are available a condensation cure type and an additive cure type. the condensation cure type is strongly dependent on the catalyst and produces by-products like alcohal, While the addition cure type is dependent on temperature and produces no by-products.
RVT-2 is capable of deep section cure and its cure rate can be controlled, Also it provides excellent electrical insulation, heat resistance, cold resistance, weatherability, and impact absorption, as the uniqe features of silicone. These resistance result in superior ease of use for various applications and improvement of the quality and productivity of finished products. RVT-2 is used primarily as electrical insulating and materials foe electrical and electronics, vacuum casting mold and  various forming mold.

Silicone Sealant is a one component , silicone RTV-1 designed for sealing as adhesive for electric parts.

Application : 

• Head Light Gasketing 
• Bus side glass glazing 
• Adhesion and sealing of polycarbonate 
• Plastic Bumper Sealing 
• Adhesion and sealing of other metals and plastics
• Protective covering , sealing and coating electric and electronic parts
• Adhering hybrid board and the case 
• Sealing and coating for electric & electronic and automobile industry

RVT-1 is a one-component room temperatyre vulcanizing silicone that cures to silicone rubber on exposure to atmospheric moisture at room temperature. RTV-1 performs excellent adhesion to most of all sudstrates without primers, outstanding weatherability assuring semi-permaent use and excellent electrical properties, RTV-1 is used primarily as adhesive and coating materals for various industries inculding electrical, appliances, and mechanical.

These Peroxides have following advantages for use in Silicone Rubber Molding Application:

• Almost Smell-less, with partial Sweet Smelling Odour
• No Discolouration & No Yellowness and best used for Transparent Products
• Best Physical Properties Achieved
• Proper and easy dispersion in Silicone Rubber because all the grades are based on Silicone Carrier [ HX is Pure Liquid]
• Ready Stock Available

Application : PEX Pipes , Polymer Modification , Technical rubber goods , Silicone Rubber Crosslinking.

Masterbatch carried in EPR , used in Rubber Industry , Smellless peroxide and FDA Approved which easily blends in Rubber Mixes

Dicumyl Peroxide in 40% Silicone

Crosslinking of Natural Rubber , Synthetic Rubber , Thermoplastic Polyolefins

Crosslinking of silicone Rubber, recommended for hot air vulcanization and can be used for curing without external pressure

Application: Crosslinked Polyethylene, CR-PP, Engineering Plastics, GPPS, Inks, Paints, PEX, Polypropylene (PP), Polystyrene (All Purpose), Polystyrene (Expandable), PS, Rubber Vulcanization, Styrene Butadiene Rubber (SBR), Styrenic (co)Polymers, VPE, Wire and Cable, XLPE

Calcium Oxide P is a powder of 80% calcium oxide coated with DOP to delay reactivity and is used as a desiccant in rubber compounds and PVC Plastisol which ar cured pressureless (Micro wavesystem, LCM, Hot air or Fluid bed).
Moisture which presents in all rubber and PVC chemicals, especially fillers, will be absorbed and the calcium oxide will changes to calcium hydroxide after reaction with the moisture.

Calcium Oxide Gr is a soft granule of 80% calcium oxide coated with special despersing agents to delay reactivity and is used as a desiccant in rubber compounds which are cured pressureless (Micro wavesystem, LCM, Hot air or Fluid bed).
Moisture which presents in all rubber chemicals, especially fillers, will be absorbed and the calcium oxide will changes to calcium hydroxide after reaction with the moisture.

Normal working temp. – 65 C to 250 C. This polymers is well known as NEOPRENE. This multi purpose synthetic rubber has proven performance in thousand of applications because of chlorine content so chief characteristic of the polymer is an Flame proof. Excellent ageing properties in Whether and Ozone. Excellent Flex crack resistant. Excellent water resistant, Good resistant to parafenic and Nepthenic Oils, Alkalis, Acids. 
Applications :
Industrial flameproof hose, Flameproof belt. DustCover wire clad adhesives. 

Harmonized matching Heatproof ,Gas Permeations Proof ,Cold Resistance ,Oil Proof ,Better heatproof Than Cr.
Applications :
Automobiles Fuel Hose ,High Pressure Hose Oil hose Tube ,Air In take hose ,Engine Return Hose  / Diaphragm ,Vacumm Diaphargm ,etc.

Normal working Temp. – 45 to 100 c. This is the rubber widely used which has  good physical properties like Tensile, Elongation, Excellent Resilience, Abrasion Resistant, Good Rebound, Tear Resistant, Good adhesion to metal, with Excellent Elastic properties. 
Applications :
Automobiles Tire Shoes ,Industrial hose Belt Dust proof goods etc.

Normal working temp. – 45 C to 110 C. This general purpose Polymer has good Resistant to dilute organic and inorganic acids. Resistant to non polar  solvent, Alcohol and brake fluids. Advantage of this polymer is dynamic Fatigue Resistant, Abrasion Resistant, High heat built up, Water resistant. 
Applications :
Automobiles Tire Shoes ,Industrial hose ,Rubber waterproof Cloth,Sports goods,Belts Dustproof goods,etc.

High Thermal Resistance and Cold Resistance .Normal working temp. – 75 C to 300 C. This high molecular weight poly organo siloxanes has substitute group of  methy and vinyl on the polymer chain. 

This polymer have high thermal Resistant and very good resistant to attack by Oxygen, Ozone, Sunlight, and wide temperature range. 

This polymer often used for medical products and for Die – electric properties.  

The advantage of Powder form rubber :

• Convenience of use
• Reduction of energy consumption by eliminating the plasticization stage
• Accuracy of dosing and improved quality of finished products
• Possibleity of using the equipment for processing plastics

Applications :
Powder form rubber is used as a modifying additives that increases the impact strength, frost resistance, oil-resistance and elasticity.

food grade synthetic rubber is a high styrene, hot emulsion styrene-butadiene copolymer using vegetal fatty acide as emulsifier and coagulated with salt-acid. It is  stablized with bht antioxident. The product complies with u. S. Fda regulation 21 cfr $172. 615 referenced to sbr used for chewing gum, 21 cfr 177. 260 indirect food additives : polymers. It meets the requirments in the food chemical  codex for 50/50 type sbr. 
applications : 
specially designed for bubble gum, chewing gum giving firmer chew and larger bubbles.

Translucent general purpose molding silicone rubber products are heat-curing silicone rubbers which are widely used for molding in various industries. They excellent 2 roll mill workability, mold release ability and have various shore A hardness of 30, 40, 50, 60, 70 and 80. These grades have good rebound resiliency and mechanical properties, and are used in various applications such as keypad and kitchenware.

Extruding silicone rubber products are compounds with shore A hardness 30, 40, 50, 60, 70 and 80. They are designed to facilitate mixing with extruding fillers and additives.Along with mechanical and eletrical properties, these products have excellent process ability and usually made by an extruding process, but compression molding method is also possible.

These product have a lower hardness (shore A hardness 8 - 20) in the cured state.
They can be used in silicone rubber product such as sporting goods and medical articles that require a soft feel.
Characteristics

• Low shore A hardness and high elongation property
• Excellent process ability in molding & injection
• Complies with BfR and FDA food contact regulations

Applications

• Swimming goods (Swimming caps, goggle bands)
• Baby care articles (Wears, covers)
• Highly elastic articles (strip, tape)

Muffler Hanger
Turbo Charger Hose
Oil Filter
Spark Plug Boots
Oil - bleeding silicone elastomer
Benefits 

• Excellent process ability
• Excellent mold releasing ability
• Excellent machanical properties

High trasparent silicone rubber compound which has hardness 50, 60, 70(Shore A) in the cured state. It can be used for Manufacturing silicon rubber products having excellent transparency.
Applications
Goggles, tubing and profile etc

These products have excellent mechanical properties including high tear strength and used for applications requiring high reliability such as parts with complicated shapes, large molded parts, etc 40 and 55 hardness show good heat stability by themselves, but 60 and 70 hardness show good heat stability additive.

Oil bleed products are special silicone elastomers which are bleeding silicone oil from cured rubber. This allows for easy assembly and waterproof properties. They can be used by various processing method such as extruding, molding, calendaring, etc
Characteristics
Good heat and oil resistance properties
Waterproof & easy assembly by suitable oil blrrding
Excellent process ability in injection, transfer molding
Good mechanical properties

These products are specially designed for addition curing systems. Properly post-cured articles can comply with BfR and FDA food contact regulations.
Characteristics
Excellent process ability in extruding & molding, etc
Excellent mechanicla properties & Good transparency
Non-blooming & non-yellowing properties
Complies with BfR and FDA foog contact regulations

SH5190U is a high hardness silicone rubber compound which have hardness 90 (shore A) in the cured state.
Applications
Baby spoon, living appliance, key pad etc

This is a silicone rubber molding compound for high voltage insulating applications and is already mixed with a catalyst. Typical applications are suspension are insulators, line posts, surge arresters, cable terminations, and connectors.
Characteristics

• Excellent tracking & ersistance property
• Excellent resistance to weathering and air pollution
• Excellent electrical insulation properties
• Superior water repellent capability
• Excellent process ability in injection molding

These products are designed to have excellent stability against compressive strain without a secondary curing process in a wide temperature range.The products can be mixed suitable ratios to create intermediate hardness.
Characteristics

• Low comperssion set
• Heat and reversion stability

These products are highly transparent and mechanical strong silicone rubber compounds which have shore A hardness from 30 to 70 in the cured state. They can be used by various processing methods of extruding, molding, calendaring, etc. They have a good heat stability additive.
Characteristics:-

• Excellent mechanical and electrical properties
• Excellent process ability in extruding & molding, etc
• High transparency
• Good heat resistance with heat stabilizer additive
• Complies with BfR and FDA food contact regulations

Extrudable base silicone rubber compounds can be used not only with extending filler(inorganic filler such as quartz, etc)but also by themselves.
Characteristics

• Excellent mechanical and electrical properties
• Excellent process ability in extruding & molding, etc
• Good transparency
• Good heat resistance with heat stabilizer additive
• Complies with BfR and FDA food contact regulations

Silicone rubber wire & cable extrusion grades with shore A hardness of 60 and 70.These products have excellent extrusion properties and can be used for wire & cables in a wide tempertmre range.
Thermo stable silicone rubbers for wire & cable.They can be used in a wide tempertmre range and exhibit good electrical properties.
High dielectric strength cable extrusion grades with shore A hardness 70.This product has an excellent property and can be used for wire & cable in a wide temperature range.

Fluoroelastomers are used in a variety of high performance applications, where long term reliability is important even in severe environmental applications.

It is a fluoroelastomer precompound which include copolymer of hexafluoropropylene and vinylidene fluoride, curatives. Calcium hydroxide is not required, the problem caused by Calcium hydroxide such as dispersion and hygroscopy can be eliminated.
It is designed for bonding seals.

Very good weatherproof ,Heatproof and Fuel proof Good acid resistance and Chemicals proof.Normal working temp. – 20 C to 250 C. This polymer is well known as  FKM . FKM are used for a vast range of sealing applications due to its broad spectrum of Chemicals And Oil media and wide range of temperature. 

FKM exhibits excellent resistant of Mineral oils, Fuels, Steam, Alcohol Aliphatic and Aromatic hydrocarbons, Alkalis. finds wide applications in automotive parts and parts in a variety of heavy - duty equipment.

Fluorosilicone Rubber is speciality compounds which contains properties of both fluoro elements and silicone.
Features :

• Very low compression set
• No post cure potential
• High resiliency
• Good tensile strength
• Good handling properties
• Easily pigmented
• Excellent solvent / fluid resistance
• Retains properties over a wide temperature range

Rubber, plastic, and silicone colouring solutions : 
colour masterbach for the rubber industries

colour masterbatch for silicon gum and fluid

epoxy pigment dispersions

plasticiser pigment dispersions

aquaeous pigment dispersions

wax bound pigment dispersions

dry powder blends and dry liquids

from bulk supply to sachet packs

Petroleum resin is a c5/c9 aromatic hydrocarbon used in industrial applications. It has a tackifying effect and is suitable for use in rubber, paint, printing ink, adhesives and other 
areas where tackiness is required

petroleum resin with melting point in the range of 90°-110° celcius is used as a tackifier for various synthetic rubbers including sbr and natural rubbers, and provides excellent effects in improving processibility and performances of these rubbers.

petroleum resins with a slightly higher melting point finds an extensive range of applications as a modifier for paints and printing inks, and as a tackifier for adhesives they are specially used in rust preventive paints significantly improving various coating film characteristics including resistance against chemicals and water.

Grades avilable : 

• haf330
• fef550
• gpf660
• srf774
• mt990

Flame Retardant Modifier

Modifier that improves flame retardant property.

Mold Release Agent :

Modifier is a releasibility additive which is recommended for addition to silicone rubber formulations to obtaine releasibility.

Rubber Additives TP 316 used as dispersing agent in order to obtain better dispersion of fillers, especially carbon blacks.
Rubber Additives TP 316 improve teh rubber compound flow of all kinds of rubber compound which are calendered, etruded or used for transfer and mouldings.
Rubber Additives TP 316 Improves the surface finish of vulcanisates.
Rubber Additives TP 316 compatible NR.SBR, EPDM, CR, NBR, IIR, CSM, BR, EVA, ECO,CM.
Rubber Additives TP 316 does not influence the peroxide curing negatively.

Rubber Additives S 80 is coated soluble sulphur containing dispersing agents, wetting agents and EPDM rubber. Incorporation and dispersion of the sulphur are taking place without formation of agglomerates and local concentrations.
Rubber Additives S 80 can be added to any natural rubber and synthetic rubber compound which is sulphur cured.

Rubber Additives TP 133 is used for the treatment of vulcanized rubber compounds in the form of sheet or strip to prevent surface sticking.
Rubber Additives TP 133 is paste type agent. It is non foaming

Rubber Additives TP 130 is used for the treatment of vulcanized rubber compounds in the form of sheet or strip to prevent surface sticking.
Rubber Additives TP 130 is powder type agent. It is not dusting and non foaming

Rubber Additives Zn : 
1-can replace stearic acid
2-Reduces stess relaxation
3-Improve building tack
4-Improve dynamic properties
5-Reduces comprssion set at low temperature.

Rubber Additives TP 342 is highly effective process additive and mould release agent.
Rubber Additives TP 342 is a internal lubricant and filler dispersant.
Rubber Additives TP 342 compatible NR,SBR, EPDM, CR, NBR, IIR, CSM, BR, EVA, ECO,CM.
Rubber Additives TP 342 suitable for pressureless vulcanisation process e.g.
UHF, LCM, Hot Air and Fluid Bed.
Rubber Additives TP 342 does not influence the peroxide curing negatively.

Rubber Additives TP 344 is multi purpose processing additive for a wide range of polymers.

Rubber Additives TP 344 is a internal lubricant and filler dispersant for carbon black and silica.

Rubber Additives TP 344 improvement of mould flow, extrusion flow and surface finish.

Rubber Additives TP 344 compatible NR,SBR, EPDM, BR, NBR.

Rubber Additives TP 344 suitable for pressureless vulcanisation process e.g.
UHF, LCM, Hot Air and Fluid Bed.

Rubber Additives TP 344 does not influence the peroxide curing negatively.

• Reduces compound viscosity with internal lubrication.
• Improve overall flow and processability of most polymers.
• Physical peptiser for NR.
• Not suitable for halogen-containing elastomers
• Can partially replace stearic acid

Soluble Sulphur containing Wetting agents, dispersing agents, EPDM Rubber. Can be added
to natural Rubber and Synthetic Rubber which are sulphur cured .

Treatment of unvulcanised rubber compounds in the form of sheet or strip to prevent surface sticking. 

Used as Activator in Natural Rubber, Can replace stearic acid, Reduces stress relaxation, Improve building tack . Improve dynamic properties. Reduces compression set at low temperature.

Better elasticity and wearability than NR Good Crashworthiness and Cold resistance.
Applications :
Automobiles /airplane Tire, Shoes,Dustproof Rubber,Rubber Roll Belt etc

Better weatherproof ,Acid Resistance andOzone proof,than CR, IIR,Bettert Chemicals Proof mineral Acid Proof and Alkaline Prof ,than CR.
Applications :
Power Steering hose ,tank linning ,Roofing Sheet , Rustproof packing ,Heat /rust proof roll ,Handroll Belt ,Rustproof ,Rustproof Paint,etc.
 

Good weatherproof ,ozone-proof gas permission-proof insulatings properity, heat proof chemicals proof waterproof and high temperature tearing. 
Applications :
car air conditioners hose , automobiles tube, curing bag ,roofing,wire clad steam hose ,etc. 

Denka A-90 with increased reactivity with isocyanate and is therefore ideal for improving both the initial and final strength, as well as the heat resistance of two-part adhesives that also use isocyanate. This grade is widely used in shoe manufacturing and conveyor belts .
 

Two-componets type and allows easy addjustment cure rate.
Non-corrosive metals.
Excellent weather resistance.
Outstanding physical properties (high-modulus & high-elongation).

Benifits

• Two-components type and it allows easy adjustment cure rate.
• Non-corrosive metals.
• Excellent weathering resistance.
• Outstanding physical prperties ( High-modulus & high-elongation ) for structural sealant glazing.

Benefits
Oil, fuel and hydraulic fluid resistance.
Features

• Oil, fuel and hydraulic fluid resistance.
• Excellent durability and high performance.
• Self-levelling.

Benefit

• Low shrinkage.
• Good adhesion.
• Excellent weather resistance.
• Non-corrosion.
• High elongation.
• Room temperature cure.
• Non-staining.

Provided that the compounds are formulated and processed correctly, the vulcanizates have excellent resistance to weathering and ozone, good to very good resistance and low temperature flexibilty, low electrical conductivity and satisfactory resistance to polar chemicals.

Blended with IIR for Inner Tube Manufacturing & Mechanical Goods

Good High Temperature Durability ,Dynamic Resistance ,Low Temperature Flexibility ,Weather proof ,Ozone Proof ,Flections Fatigue Resistance ,Crashworthness .

Normal working temp. – 25 C to 175 C. Acrylic elastomer are copolymer based on two major components of Ethyl acrylate and Butyl acrylate with monomers. 

The lake of double bonds, ACM have excellent resistant to Oxidation, Ozone, Sunlight, Weather and Heat. Excellent resistant to corrosion, Hydrocarbon oils, Mineral oils. Not recommended to use with Water,  Steam, Acids and Alkalis. 

Good Mechanical property ,Cold Resistance ,Oilproof ,Flameproof ,Comfortable Color ,Dynamic Fatigue Better Thermal Resistance Than Cr

Normal working temp. – 25 C to 150 C. HNBR polymer containing little or more  hydrogenation. Polymer have improved  properties depends upon on the degree of hydrogenation. 

Polymer has outstanding resistant to Oxidation, Heat, Ozone, 
Weather, Resistant to Sulphur containing oils, Amines, Fuels, Greases, Aliphatic hydrocarbons and industrial chemicals with good Mechanical properties.  

This product not only has a high level of flame retardant property (UL 94 V-O)but also good thermal conductivity (about 1.0W/m.K) to dissipate the heat from the electrical and electronic appliances.It helps prevent heat buildup and extends the devices life.

These product have a high level of flame retardant property(UL 94 V-O) and electrical characteristics,Which are suitable for electric and electronic product as well as excellent mechanical properties.Tey are widely used for anode caps, back light holders, gasket ofvarious display units, and construction matrials such as fire-proof door gaskrt requiring flame retardant performance.

poly dimethy is siloxane have low, medium, high viscosity polymers. Having range from 0. 65 cst to 500000 cst depending upon application silicone fluids of various viscosities are used accordingly. 

Hydroxy Silicone Fluid silanol fluids are used as base ploymer for rtv-1 (room temperature vulcanizing one-component) sealants. They are water-clear, odorless, oily fluids. Silanol fluids are available in viscosities ranging between 5000, 20000, 50000, 80000 cPs at25 C.

Methyl terminated mono functional silicone fluid developed for textile softener use. It can be easily emulsified to stable micro emulsions which give durable softness and smoothness to cotton, blending cotton woven fabrics and knitted product. 

Silicone Antifoam Compound is used where product or process foaming problems are encountered with pressurebeck dyeing process such as jet dying machines. the actual cause of foam is a complicated stidy in physical chemistry, its existence presents serious problems in both the operation of industrial processes and the quality of finished products. Chemical defoamers have proven to be the most effective and economical method to control foam.

Vinyl terminated silicone fluid is a base polymer for addition-curing RVT-2k (room temperature vulcanizing two component), LSR (liquid silicone rubber) silicone rubber. the terminal vinyl goups take part in the vulcanization reaction with Crosslinking agents in the presence of Catalysts. wide range of viscosities are available from 100 cps to 150000 cps couids are used for sevcceal application accordinly.

Applications  
O - ring, Gasket, Sheet, Hose
Key Performance Properties

• Excellent Heat/Steam Resistance ability 
• Well balanced physical properties

Features
Steam Resistance silicone rubber

Products

• Copolymer
• Terpolymer

Application

• O-ring
• Gasket
• Valve steam seals